SUN RAY INVADER DX

(Compatible with White's DFX, DFX 300, MXT, MXT PRO, M-6 and the new Spectra V3/V3i/VX3)

Sun Ray Detector Electronics is proud to announce our new Invader™ series of aftermarket accessories for White's metal detectors! The new Sun Ray Invader DX-1 Target Probe has been developed to satisfy the pinpointing and retrieval needs of DFX/DFX 300/MXT/MXT PRO/M-6 & SPECTRA V3/V3i users. We have received many requests for in-line target probes by White's and other detector brand users for several years due to the popularity of our quality in-line probes for the Minelab Explorer and Sovereign/Elite. Now White's owners can enjoy the same benefits a quality Sun Ray in-line probe has to offer! Here are some of the features of the DX-1:

Fully compatible with DFX, DFX 300, MXT, MXT PRO & M-6 models! The DX-1 is precision built to ensure peak performance.

(Spectra V3/V3i Compatibility is as follows:

WHITE'S SPECTRA V3/V3i AND SUN RAY INVADER DX-1 TARGET PROBE COMPATIBILITY

The Sun Ray Invader DX-1 has been determined by us and the engineers at White's Electronics in Sweet Home, OR to be compatible with the new Spectra V3 with the following exceptions:

(1) The probes we have tested on the V3 did not overload on RX 15 (gain) with TX Boost on. However, the probe may or may not overload at those settings due to slight tolerances from probe to probe just like slight tolerances from one coil to the next. (See (2) below.

(2) However, the stock White's 10" DD coil may or may not overload with the DX-1 in-line depending on the tolerances from coil to coil. This has nothing to do with the probe or coil involved, rather with the switch (for switching from coil to probe and visa versa)

(3) It was found that by either reducing the RX gain a number or two ,or, disengaging TX Boost resolved the problem.

(4) In most hunting conditions RX gain cannot be used at maximum setting unless you are detecting on neutral ground such as a beach with no mineralization, especially with TX boost engaged.

(5) Other V-3 compatible coils, including non V-tuned coils (whether factory or after-market) may overload at max RX and TX Boost and may require a lower RX setting (or TX Boost disengaged). How low will depend on the coil and ground conditions, however, our tests showed other coils we tested only had to be lowered on RX a few numbers to cancel the overload if TX Boost was left engaged. (NOTE: Various tests described above were conducted by both Sun Ray Detector Electronics and White's Electronics in Sweet Home, OR. White's Electronics has approved the above compatibility statement.)

Accurate "bulls eye" pinpointing on coin size targets up to 3"+ deep depending on detector used, settings, ground and moisture conditions!

NEW! Lighter weight, waterproof/submersible 6" X 1" diameter probe mounts on top of upper shaft. DX-1 probe and cable weigh approx. 5 oz. DX-1 switch box, connectors, cable and probe clip, etc. weigh approx. 5 oz. - approx. 10 oz total! (Optional box mount probe clip attachment available for those wishing to mount probe along side of detector control housing).

New red Probe Tip Cover installed to prevent wear and tear on the probe tip. Replacement covers available from your authorized, stocking Sun Ray Dealer.

While the DX-1 probe is waterproof the switch box is water resistant and must not be submersed. (We use the same connectors as White's.)

DX-1 incorporates all of the same functions as the stock coil including accurate visual and audible target ID along with identical pinpoint functions! (Depth reading will be off due to the probe's diameter which is normal.)

High quality custom made, durable probe and connector cable used for precision performance. Probe incorporates a very flexible heavy duty custom 32" straight cable with strain relief for "tangle free" operation.

Quality high performance toggle switch used for peak performance! (Minimum 100,000 mechanical life operation-as described in manufacturer's specs)

Toggle switch shuts off coil as it turns probe on and vise versa. Coil and probe are never on at the same time.

DX-1 switch box is conveniently mounted on detector pole attachment in a neutral position (for both right and left hand users) and to prevent toggle from being accidentally switched or bumped by user or damaged by tree limbs, brush, etc. if switch box is brushed or hit during detecting.

No external buzzers, vibrators or lights are needed as all target responses are heard clearly through your detector headphones!

No extra batteries required as the DX-1 utilizes the detectors power source.

Complete installation & operation instructions included.

Experience a Sun Ray in-line probe on your detector and you'll wonder how you ever got along without it!!

Sun Ray Detector Electronics has been manufacturing multi-frequency in-line probes since 1997. Our design and production engineer has been designing and building probes for over 11 years which include in-line multi-frequency, stand alone as well as pulse and has designed and built pulse detectors and circuits. The popularity of our in-line probes is well known in the metal detecting industry and satisfied customers tell us our quality is second to none!